Как подключить телефон к старому музыкальному центру
На нем есть разъём под названием «phones»,но при подключении к нему телефона ничего не происходит, а выбора aux на самом центре нет, может у кого была эта модель- Technics SH-EH790
Вход должен быть, либо LINE IN, либо AUDIO IN . Спереди или сзади разъёмы смотри (как на фото) .
Сзади смотри разъёмы, там должны быть «тюльпаны» (RCA), а тебе просто переходник нужен, вроде такого
Technics SC-EH560 RU
Для ознакомления с инструкцией выберите документ в списке. Инструкцию можно просматривать онлайн без регистрации и без скачивания. Если вы не нашли необходимую информацию по устройству, то вы можете задать вопрос в обсуждениях.
Если вам необходимы дополнительные материалы по устройству: драйвера, прошивки, дополнительные сведения, вы можете отправить запрос модераторам сервиса, которые постараются вам помочь.
Если вы хотите поделиться опытом использования устройства или хотите рассказать о его достоинствах или недостатках, то оставьте отзыв.
Technics SH-EH560
I wondered if they could help me in a situation.
I was given a Technics SH-EH560 Stereo System by a family member which he no longer used and also had no speakers. What happens is that I connected some speakers that I had in good condition from Kenwood 8 ohms but the sound comes out full of distortion when you press with them.
Honestly, I don't understand any of these things and I limited myself to connect in the places that seemed to be the most correct, but as the system on both the right side and the left side has 3 exits, I didn't know if I was calling in the right place.
I appreciate your help.
- Add to quote
- ShareOnly show this user
According to the owner's manual, the amplifier section of that Technics stereo unit has LOW/MID/HIGH outputs that correspond to LOW/MID/HIGH inputs on the left and right speakers that originally came with it.
- at low volumes, the audio probably just sounds muffled; and
- at higher volumes, the fact that you're pushing only low frequencies (LOW: 54W/ch. / 100Hz / THD10% / 6 ohms) through the speakers' woofers and tweeters is likely the cause of the distortion.
- the combined impedance; and
- the different wattage ratings,
Personally, I'd get rid of the Technics system and replace it with a basic A/V receiver ("AVR") or stereo receiver.
- Add to quote
- ShareOnly show this user
The high – mid – low connections tells me that it might be a tri-amped system, meaning separate amplifiers for the highs, mids and lows. If that’s the case, trying to combine the outputs to a single “regular” speaker will probably blow out the amplifiers.
Either way, that system was designed to work with the speakers it came with and nothing else.
Regards,
Wayne A. Pflughaupt
Equipment List
"A nice mid-fi system," according to an audiophile acquaintance.
- Add to quote
- ShareOnly show this user
@pesquita
Hi bro, not all is lost, with a bit of work you could get them going, crap-style but still.
Those speakers you got, are 2 way speakers, meaning they have a speaker for high tones, and one for mid and low.
You need to open them up, remove the wires from these 2 speakers to whatever crossover filter they have inside.
Now comes the hard part, you need to choose if you want to hear lows or mids from them. Cant have both. I would go with mids.
If you choose to go with mids, pull 2 wires from the tweeter (small speaker) to the grey plugs of the amplifier and 2 wires from the bigger speaker to the blue plugs of the amplifier.
Sound will not be ideal but it will be usable until you get your hands on a 3 way speaker set to use with it.
If you crank up all bass related settings, it might actually push the mids low enough to give your speaker and ears some joy.
Why Technics went with this ass-tard solution of putting the crossovers inside the amp instead of inside the speakers is beyond me.
The logistics alone of having 6 wires to each speaker is mind blowing.
They make hell of an audio line this thing aside though.
- Add to quote
- ShareOnly show this user
@pesquita
Hi bro, not all is lost, with a bit of work you could get them going, crap-style but still.
Those speakers you got, are 2 way speakers, meaning they have a speaker for high tones, and one for mid and low.
You need to open them up, remove the wires from these 2 speakers to whatever crossover filter they have inside.
Now comes the hard part, you need to choose if you want to hear lows or mids from them. Cant have both. I would go with mids.
If you choose to go with mids, pull 2 wires from the tweeter (small speaker) to the grey plugs of the amplifier and 2 wires from the bigger speaker to the blue plugs of the amplifier.
Sound will not be ideal but it will be usable until you get your hands on a 3 way speaker set to use with it.
If you crank up all bass related settings, it might actually push the mids low enough to give your speaker and ears some joy.
Why Technics went with this ass-tard solution of putting the crossovers inside the amp instead of inside the speakers is beyond me.
The logistics alone of having 6 wires to each speaker is mind blowing.
They make hell of an audio line this thing aside though.
Как соединить eh560 technics с телефоном
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Preview of TECHNICS SH EH560 [1st page]
Click on the link for free download!
Preview of TECHNICS SH EH560 [2nd page]
Click on the link for free download!
- Also known:
TECHNICS SH EH-560 EH560 EH 560
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Sziasztok. Elorebocsatom, hogy ekezetek nelkul irok. Ne ragjatok be ram.
Van ez a Technics su-a700mk2 tipusu erosito. Aktiv a vedelem. Nemhiaba, mert a vegfok bementein +20v van. Mindketton. Eredetileg +20v es +40v volt, es eljutottam az AN7062-ig, aminek a 18. laban -10.7v helyett +6v volt. IC csere sem hozott valtozast, igy kezdtem mericskelni a diodakat, igy akadtam ra egyre (D405) ami rovidzarat mutatott az aramkorben, kiveve oda-vissza vezetett. Csere utan beallt az egyensuly de nem a kivant mertekben — a Q401-402 kollektorain 2.5v helyett +20v van, a B-E fesz 0.6-0.7V mindkettonel. DE! A 18. labon -10.7V helyett most -17v van. Nem egyszer mertem meg, leellenoriztem mas modell rajzan is -10.7v van. Lehet, hogy a RSN6000 lenne hibas?